Skip to main content

Trio Kenwood KD-1033 turntable main bearing service

  One of my first posts in this blog was regarding the servicing of the Pioneer PL12D turntable, and that has proven to be the most popular by a significant margin. The Pioneer PL12D had its competitors, and probably the most popular alternative was the Trio Kenwood KD-1033 turntable. I use both names (Trio and Kenwood) as the company operated under different names in different markets. In the UK they were Trio, possibly because the brand Kenwood was most famous here for food blenders. 95% of a KD-1033 is similar to  Pioneer PL12D, and servicing them is very much the same process. Both are belt drive , have an AC synchronous motor,  mechanical speed change , a main bearing, sprung top deck and rubber motor mounts. the KD-1033 uses a different type of anti skate mechanism, employing a thread and weight. The plinth is shallower with an internal cross brace. One aspect that is different is the design of the main bearing, and servicing it is a little harder than a PL12D. The Pioneer main b

what to do with an old hard drive





Over the years I have accumulated a number of old PC hard drives. Some were mine, other from neighbours & friends who asked if I could "fix their PC". It occurred to me that I had a burden of responsibility for these disks, if someone got hold of them they might be able to extract confidential data. In each case I had determined that the disk was dead or dieing, having failed the manufacturers full surface test (via Ultimate Boot CD - UBCD), but conceivably the disk could be attached and read on another computer. They might contain personal data - so I decided to put these disks beyond recovery.

First you have to dismantle the hard drive. this involves removing all external stickers from the disk , and with a torx driver (purchased from your local hardware shop - in my case the always helpful W. C. Baker of Fleet ), remove all the bolts which hold it together.

An excellent video of how to dismantle a similar hard drive is here :

Once the disk is in bits then probably the data is beyond economic recovery. I doubt the platters are interchangeable, and they do not appear to have manufacturers model numbers or any markings at all. Putting one of these platters back in a different model of drive is unlikely to make it readable IMHO, though I dare say a Police forensic department or similar could extract data still, should they have a burning reason to do so. But it could take days.



Having dismantled the drive you have a number of useful artefacts :

1) the shiny platters(s). These are perfect round mirrors. They could be used as small camping mirrors, for bird scares, wind chimes (they ring) but I decided to make them into a solar collector. I went to my local hardware shop (W.C. Baker of Fleet) and described roughly what I wanted to do, leaving out the bit about building a death-ray. It turned out that standard UK plumbing washers are exactly the right fit. These are 1" / 24mm diameter rubber washers of approx 3-4mm thickness, with a hole in the middle. These provide a snug fit for the hole in the centre of all hard drives. Better still the discs can be tilted slightly on the washer fitting, enabling a degree of focusing of the beam. I attached all 9 to a piece of wood. this enabled me to fix this unit in my garden and direct and focus the "death ray" onto a specific target. You can see the awesome effect of this in the picture at the top. You can also see how the projected light from the sun was focused onto my wood pile. It did not spontaneously burst into flame BUT you can clearly see the focused beam in the picture and it was noticeably hotter when I dared to put my hand into it. My hope is that, over time, it will slowly dry out those fresh cut logs .


The other components you have from the disk drive are :

2) A very strong magnet or two - these work as the best fridge magnets you will ever find - you can probably hang the phone book on your fridge with one of these.

3) The disk controller board. This is the circuit board on the back of the disk. If you are lucky you can sell these on eBay, as they contain no data , but may have a resell value for people with the same disk, but a failed controller board. I sold around 1 in 5 and they don't go for much, just a pound or two but that's OK.

4) the drive case - the chunky black part is high grade aluminium and can be recycled at any Alu recycling plant, or by local charities for funds. Near me is an Aluminium recycling plant (T Baker (JNR) Ltd of Farnham) who, if you ask, will donate your recycling proceeds to the Phyllis Tuckwell Hospice, a very worthwhile local charity

5) The drive heads. this is a wonderful looking piece of engineering. I have no particular idea what to do with them. they might be used as strange jewellery or parts of a robotic fancy dress party. I'll save these for future use.

6) Assorted precision fittings and washers which could be used for all kinds of projects, jewellery, collage etc. There are a set of bearings which the drives head unit uses to pivot.

7) The stepper motor. These electric motors require some logic from the driver board to work, so I don't think you can use them as 12v motors. Again - a future use will present itself, but for the moment they provide nice little stress-busters, as rotating the centre part produces a a satisfying little click as it goes round.

8) The disk "lid" i.e the silvered metal sheet which covers the entire disk enclosures top surface, as opposed to the side with the controller board. On closer inspection, once removed, you will see that this appears to be a sheet of metal. In fact if you tap it you see it's heavily damped. My belief is that this is a sandwich of 2 metals and some deadening material to reduce the mechanical disk noise. It probably also has a thread of silicone adhesive running around the entire circumference which made a gas tight seal with the main body. Leave the silicone in place. I have used a couple of these metal pieces to sit CD players on to stop skipping as they seem to act deaden vibrations.

Comments

Popular posts from this blog

Restoring a Pioneer PL-12D Turntable

 I got back into vinyl records about 18 months ago, and have collected a few hundred albums, mostly second hand. I have a number of turntables (NAD 5120, Ariston QDeck, Pioneer PL12D ) which I got also second hand. I keep a few, some end up passed onto friends, some that are too far gone are kept for spares. In most cases they have required a little work to get them running again. Last week I was lucky enough to get a Pioneer PL-12D turntable from freecycle. The lady who offered it, said that she in turn had received it from freecycle , and had replaced the belt but couldn't get on with the springiness of it, and had got a modern USB turntable. I have previously worked on one of these decks, and know what she means about the suspension system used. While this blog is specifically about this particular model of deck, many of the concepts are similar to others from this vintage. Many Japanese belt drive decks throughout the  1970's shared very similar construction, so this ma

Bracing IKEA EXPEDIT or KALLAX cabinets for greater rigidity when used with a turntable

The inevitable problem, too many records. Turntable and amplifier on top Like many record collectors around the world, I have a number of IKEA cube cabinets from both their EXPEDIT (older) and KALLAX (newer) ranges. These are easy to make, cheap to buy and perfect for record storage. The system comes flat packed and uses bolts and dowels to hold the system together. If you follow the instructions  the system is strong and should not collapse. You can augment the joints with PVA wood glue for extra strength. My turntable sits on top of an EXPEDIT 2x4 cabinet, laid along the long side, with some felt feet to support it from the floor, and you can use KALLAX in the same way. It's been great but has two problems I wanted to address : 1) Because the system has no back panel, the records  can be pushed too far back. 2) While the structure is strong and fairly rigid, there was some lateral movement. With heavy equipment on top, I found that if I nudged or knocked either top side, this all

a vintage Sonab 85S / Yamaha CP-500 turntable

The Sonab 85S turntable You'll see from this blog that I'm interested in vintage audio equipment , especially turntables and speakers. I keep an eye on ebay for potential bargains, and saw this turntable listed quite close to me and for a very good price, £60 buy it now, including 45 adapter, dust bug, DIN adapter, record clamp and a very nice Shure M95 cartridge. Condition listed as very good and with the original sonab headshell. I've been interested in this deck for sometime, as to my eyes , it's a particularly nice design, with the very simple tonearm and deep chassis. I was aware that the model , from the late 70's was a cooperation between Swedish manufacturer Sonab and Yamaha. I don't know how much was contributed by which firm, but the same deck, or one very similar is also to be found as the Yamaha CP-500, though typically in teak rather than black. There were two Sonab models , the 75 and 85, the former being a manual  deck, the latter an automatic, an